· 第十二届中国国际胶粘剂及密封剂展览会
· 缩短α-氰基丙烯酸酯胶粘剂固化时间的研
· 德国胶粘剂公司推出新的质量保证解决方
· 2010年中国热熔胶销售额或达34亿美元
· 先进纤维增强树脂基复合材料在航空航天
· 室温硫化胶层建模在透镜结构分析中的应
STRANGE PUR单组份胶粘剂
 
 
STRANGE 302PUR单组份胶粘剂
 
 产品用途:
用于汽车顶部的聚氨酯泡沫与玻纤、维纺布毛毡、无纺布、PVC革、PU革等基材的粘接
 产品概述:
  STRANGE 302PUR 粘剂是溶剂无填料单组分室温固化胶粘剂,该胶粘剂最大的特点是具有高韧性,耐震动疲劳,此外还具有耐水,耐腐蚀,环保无气味,使用温度范围宽等优点,固化时间可调,该胶主要用于汽车顶部的聚氨酯泡沫与玻纤、维纺布毛毡、无纺布、PVC革、PU革等基材的粘接。
 技术参数:
外观:黄褐色半透明液体
粘度(25℃),mPa/s :≤4000
固含量,%≥85
密度:0.9±0.05 g/cm3
拉伸剪切强度(铝/铝):≥2MPa
 施工操作:
1.该胶粘剂直接涂刷于被粘接表面,将材料贴合后,轻轻按压使粘接剂充分浸润,放置或加压放置一段时间,使胶粘剂基本固化,一周后达到最佳。
2.该胶粘剂易与空气中的水份反应,使粘度增大,严重时发生凝胶。因此,打开包装后应尽快使用。用不完时,应将包装桶的桶口擦净,盖紧。
3.施工可用手工刮板或滚筒上胶,也可用单组份机器上胶.最好是连续施胶。
4.该胶粘剂可喷涂,使用量约在80~150g/m2
5.反应速度可以根据实际要求及配套设施调节。
6.若胶粘剂粘度过大,可用丙酮或乙酸乙酯稀释。
7.未固化胶水可用洗液清除,固化后的胶体用机械方法清除。
 包装及储运:
1. 本品为单组份,包装:55加仑 ,贮存时间:6个月
2. 该原料应储存在室内通风干燥处,注意防水,防潮,防湿,以免吸湿固化造成失效。
3. 使用后,包装容器应立刻盖紧,以免失效。
本品为非易燃易爆品, 以上提供的所有内容均基于我们的测试和数掘,是准确可靠的,但不能认定为任何保证和承诺。
 
                         STRANGE 302PUR single-group adhesive
Application: used for adhesive bonding of polyurethane foam at the top of the car with glass fiber, woollen felt, non-woven fabric, PVC leather and PU leather
Product overview: STRANGE  302pur adhesive solvent is packless one-component room temperature curing adhesive, the adhesive of the biggest characteristic is high toughness, resistant to vibration fatigue, moreover also has water resistance, corrosion resistance, no smell, environmental advantages of using a wide range of temperature, curing time is adjustable, the glue is mainly used in automobile at the top of the polyurethane foam with glass fiber, spinning, non-woven, PVC leather, PU leather cloth felt base material such as glue.
Technical parameters: appearance: yellowish translucent liquid
Viscosity (25 ℃), the mPa/s: 4000 or less
Solid content, % greater than 85
Density: 0.9 + / - 0.05 g/cm3
Tensile shear strength (aluminum/aluminum) : greater than or equal to 2MPa
Operation:
 1. The adhesive to be adhesive surface directly, the material after laminating, gently press the adhesive fully infiltrates and placed or pressure placed a period of time, make the basic curing adhesive, a week after the best.
2. The adhesive is easy to react with moisture in the air to make the viscosity increase, and gelation occurs when severe. Therefore, the packaging should be opened as soon as possible. After use, the barrel of the drum should be cleaned and tightly closed.
3. The construction can be made by hand scraper or roller, and also can be used as a single unit of machine glue. It is better to glue continuously.
4. The adhesive can be sprayed with about 80 ~ 150g/m2.
5. The reaction speed can be adjusted according to actual requirements and supporting facilities.
6. If the adhesive viscosity is too high, it can be diluted with acetone or ethyl acetate.
7. The uncurable glue can be cleared by cleaning liquid, and the cured gel shall be removed mechanically after curing.
Packing and storage: 1. This product is a single unit, packing: 55 gallons, storage time: 6 months
2. The raw material should be stored in the dry and ventilated parts of the room, and be waterproof, moisture-proof and moisture-proof, so as to avoid the failure of moisture absorption and curing.
3. After use, the container shall be closed immediately to avoid failure.
This product is non-flammable and explosive. All the content provided above is based on our testing and counting, which is accurate and reliable, but cannot be recognized as any warranty or commitment.
网站备案号:京ICP备17010398号