· 第十二届中国国际胶粘剂及密封剂展览会
· 缩短α-氰基丙烯酸酯胶粘剂固化时间的研
· 德国胶粘剂公司推出新的质量保证解决方
· 2010年中国热熔胶销售额或达34亿美元
· 先进纤维增强树脂基复合材料在航空航天
· 室温硫化胶层建模在透镜结构分析中的应
工业结构胶
 
 

MULTI工业结构胶

先进配方已使其性能超过了其它结构胶类,如硅酮结构胶和聚氨酯结构胶。其优异性能尤其适合工业制造粘接。如:汽车制造.轮船.核潜艇.航天等领域。除了具有永久保持弹性的特点,还有超强的粘接作用。
    胶系列有超过200种颜色可供选择,可许多材料颜色搭配。如果需要,还能在打胶后1小时后上水性涂料。它防水、可在极端的环境使用、并且抗紫外线、是结构性粘接的最佳产品。同时,它不含溶剂、异氰酸酯,挥发性有机化合物含量符合最严格的加州标准。
 

突出性能
         打胶一小时后可以上水性涂料
         永久具有弹性,极小收缩,不会开裂
         适合大部分通用性的工业制造
显著优点
         大大减少由于填缝开裂而导致的返工和维修
         99%的固含量保证最小的收缩率
         可在各种极端环境下使用

 

重要指标
主要成分:改性高分子聚合物(反应型)
状态:高粘度结构胶
粘稠度:400,000—450,000cps
挥发性有机化合物含量:9克/升(彩色),11克/升(水晶透明),46克/升(半透明)
重量/公升:1.04—1.5千克
闪点:大于94度
结冰/融化稳定性:不结冰
保存期:12个月(在24度密封状态下)
使用指南
施工温度:零下18度以上
固化后的适用空气温度:零下60度—177度
使用方法:使用打胶枪
开放时间:以六毫米宽胶条,20---40分钟(取决于温度和湿度)
粘结表面要求:表面必须清洁,而且没有油渍、油脂、水、灰尘、泥土以及任何会妨碍粘接的物质。
清洁:用腻子刀挂掉已经固化的密封胶。用矿物油清除多余未固化的密封胶。
产品特性
         性能超越单纯的硅酮结构胶和聚氨酯结构胶;
         基于最先进的聚合技术制
         在恶劣的气候条件下仍然可以轻松使用
         可填缝距离宽至25毫米
         永久具有弹性
         抗紫外线
         挥发性有机化合物含量符合最严格的加州空气标准
         涂胶1小时后可以刷水性涂料
         超过美国相关标准,可用于肉类和家禽类加工场所
限制
使用温度必须高于-18度。打胶1小时后可以上水性涂料。如果上其它涂料,建议先做相容性测试。如果缝深度超过8毫米,建议先填底料,然后再打本密封胶。不适用于密封需要长期浸泡在水中或者水平面以下的物体。
注意事项
注意:对眼睛和皮肤有刺激性。不能吞食。不能接触眼睛。也不建议长期皮肤接触。急救办法:如果吞食,不要试图呕吐,应立刻去医院求医。如果接触到眼睛,立刻用清水冲洗眼睛15分钟。如果接触到手,请用肥皂和清水清洗。如果眼睛或者譬如的刺激感一直不能消除,请立刻去医院求医。产品固化过程中会释放甲醇。如需要更多有关产品安全信息,请看安全信息表。要存放在儿童接触不到的地方。
半透明产品(编号44011)在固化过程中会释放甲基乙基酮
订购信息
产品编号   颜色                支/箱        重量          箱/产板
44001      304毫升包装         12         6.35kg          132支
            白色    灰色   黑色   透明
        

 

Advanced formula has its performance over other types of structural adhesive, such as structure of silicone rubber and polyurethane structural adhesive. Its excellent performance is particularly suitable for industrial manufacture of adhesive. Such as car manufacturing. Ship. A nuclear submarine. Aerospace and other fields. In addition to has the characteristics of the permanent flexibility and strong adhesive.

Adhesive series more than 200 kinds of colors to choose from, but many material color. If you need, but also on the glue after 1 hour after coating. It is waterproof, can be used in extreme environment, and resistance to ultraviolet ray, is the best product for structural adhesive. At the same time, it does not contain solvents, isocyanate, volatile organic compounds content in accordance with the most stringent standards in California.

Outstanding performance

After an hour of sealant can be on water-based paint

Permanent elastic, small shrinkage, won't craze

Suitable for most of the general industrial manufacturing

Significant advantages

Greatly reduced due to cracking of caulking rework and repair

To ensure that the minimum shrinkage 99% solid content

Can be used in various extreme environments

Important indicator Main ingredients: modified polymer (reactive)

Status: high viscosity structural adhesive

Consistency: 400000-450000 CPS

Voc content: 9 g/l (color), 11 grams/liter (crystal transparent), 46 grams/liter (translucent)

Weight/liter, 1.04-1.5 kg

Flash: greater than 94 degrees

Freezing/melting stability: do not freeze

Shelf life: 12 months (in 24 degrees sealing condition)

Use guide construction: the temperature of minus 18 degrees above

After curing the applicable air temperature: 60-177 degrees below zero

Method of use: use glue gun

Open time: in 6 mm wide strip, 20 -- 40 minutes (depending on the temperature and humidity)

Bonding surface: surface must be clean and no oil, grease, water, dust, dirt and any get in the way of adhesive material.

Cleaning: use a putty knife die already curing sealant. In mineral oil to remove excess not curing sealant.

Product features beyond pure silicone structural adhesive performance and structure of polyurethane rubber;

Based on the most advanced system of polymerization technology

In bad weather conditions can still easy to use

Caulking distance to 25 mm wide

Permanent elastic

Uv radiation

Volatile organic compounds content in accordance with the most stringent standards of air pollution

Can brush coating glue 1 hour

More than American standards and can be used for meat and poultry processing

Limit the use of temperature must be above 18 degrees. Glue coating after 1 hour. If the other coatings, advice do compatibility test first. More than 8 mm, if the seam depth fill out base, then whisk the sealant. Does not apply to seal will need the following long-term soaking in the water or water level object.

Matters needing attention Note: are irritating to eyes and skin. Can't swallow. Can't contact with eyes. Is not recommended for long term skin contact. First aid: if swallowed, do not try to vomit, should seek medical advice immediately to the hospital. If contact with eyes, immediately rinse eyes for 15 minutes. If the hand contact, please clean with soap and water. If the eyes or such as stimulation has been eliminated, please seek medical advice immediately to the hospital. Product curing process will release methanol. For more information about product safety, please see security information table. To be stored in out of the reach of children.

Translucent product (no. 44011) in curing process will release methyl ethyl ketone

Ordering information product number/box weight box/production plate color

44001 304 ml packing 6.35 kg (12, 132

White, grey black transparent

 

网站备案号:京ICP备17010398号